I have had a few friends ask for directions on how to make the ribbon bulletin boards I have in the kitchen and Coleman's room. I thought I would put the instructions here in case anyone else wants to try one. Unfortunately I did not take photos as the project went along, so you will have to make do with instructions and finished product.
This project can be done pretty cheaply if you already happen to have some of the materials on hand, such as the wood, batting, staples and staple gun like I did. If you have to purchase all of it you will be looking at a more pricey little project.
What you need:* 1/4 inch plywood or MDF in whatever size you want-I used scrap we had in the garage
*Fabric- enough to cover wood plus wrap over sides about 1-2 inches. Don't use anything really thin or stretchy. I used quilt material or drapery material. Use pinking shears (those zig-zag scissors) around the edges if you want it to not unravel.
* Quilt batting- (not fiberfill)- thick enough to smooth out the wood but we're not making a pillow here! Needs to be enough to wrap over sides as well about 1-2 inches
*Ribbon coordinating with your fabric pattern. I used about 15 yards for each of mine, but if you put your squares farther apart or your board is a different size that makes a difference too.
* Upholstery tacks- get them in the hardware section of your fabric store- they come in different designs. Get about 50-75 of them. Err on too many instead of too few because you will end up bending a ton of them.
* A light duty staple gun and tons of staples
* Scissors
* hammer
* ruler
* sawback hangers so you can hang your finished product
Instructions:1. Cut your wood to size. Lay your fabric and quilt batting out and cut it out just about 1" too much on all sides of your board. Pay attention to be sure the pattern on you fabric is going the way you'd like.
2. Iron your fabric. Trust me, you will kick yourself if you don't.
3. Lay your fabric face down with the batting on top (closest to the wood). Lay your board on top and center it.
4. Bring your batting around the back of the plywood and staple down about 1 inch from the edge. Do all the batting, Then follow with the fabric, pulling snugly as you go. You want it to look upholstered, but not like it has had bad plastic surgery.
5. Take care at the edges to fold them so that they lay flat. Too many staples are better than too few in this project. Trim your edges so they are neat and not too bulky, but leave a little away from the staples in case the fabric pulls a little.
6. When the upholstering is done, take your ribbon and stretch it diagonally from one corner to other. Leave about 3 inches overhang on each end, snip. While you are at it go ahead and cut two of this size. Staple one end on the back and bring it over that corner and down to the opposite- then staple it on the back, You will want the ribbon to lie snug and flat to the fabric, but not pucker the edges. I always staple 3 times on each end- 2 times with the ribbon's direction and once across. This is probably overkill, but I don't want to be repairing the thing later.
7. Repeat with opposite corners.- Be sure if your ribbon has a difference in grain or sheen from front side to back you take that into consideration and use the same side or opposite if you want a pattern.
8. Now you have a giant X. Measure however many inches from your ribbon to put the next one- I do 4" but 5" or more would work too. Cut the ribbon to length, remember to cut 2 to save time. Staple the ribbon on the back at the proper distance, then pull it across and measure at the bottom before stapling the loose end. Continue with all the ribbon until it is all latticed. You may weave the ribbon as well as you go along.
9. When you have the cross hatch all done, lay your board face up on a firm surface such as a cement floor or another piece of plywood- your tacks will probably go through the back a little, so do not use a dining table, the hard wood floor or something else like that. Take a tack, put it at the intersection of each ribbon and hammer down. These little suckers tend to bend all to heck, so practice makes perfect- good luck. You may want to have needle nose pliers handy to remove wayward tacks.
10. Turn your board over and nail down any protruding spikes. Add hangers to back and hang your project on the wall.
11. Slide your memorabilia, photos, appointment cards etc. under the ribbons and enjoy!
Be sure to email me any photos if you do this yourself. I'd love to see how someone else's turn out.
This is in Coleman's Room. It's great for holding photos, all those little craft projects as well as things he picks up along the way- such as cotton, cards and more!
This hangs in our kitchen. We keep all of our appointment cards, doctor's phone numbers, neat photos, and photos of friends and people we want reminders to pray for such as our kids in Ecuador and missionary friends around the world.
Irony in Pill Form
